Getting started (Debugger) - Revision history

Ekern: Created page with "TOC To get started: : 1. Make sure the following are true: * The
2022-11-17T23:11:52Z

Created page with "TOC <span class="f_Para">To get started: </span> : 1. <span class="f_ListNum1">Make sure the following are true: </span> * <span class="f_Para">The</span><span class="f_..."

New page
TOC
<span class="f_Para">To get started: </span>

: 1. <span class="f_ListNum1">Make sure the following are true: </span>

* <span class="f_Para">The</span><span class="f_ListBul2"> product has successfully been [[Installation and Configuration|installed and configured]], on the mainframe and on the workstation that is to host the Debugger Client.</span>

<span class="f_ListContinue2">If you are unsure, you may want to review the installation documentation and/or rerun the [[Test the end to end configuration|final installation test.]] </span>

* <span class="f_ListBul1">The Debugger Server is [[Define and start the Debugger Server port|started.]] </span>
* <span class="f_ListBul1">For the </span><var>TN3270 Debugger</var><span class="f_ListBul1">, the Debugger Server client socket port</span><span class="f_ListBul2"> is [[Define and start a client socket port (TN3270 Debugger only)|started.]] This is not needed if you only use [[TN3270 DEBUG WAIT|TN3270 DEBUG WAIT]].</span>
* <span class="f_ListBul2">The Debugger Client is [[Run, check, and verify the Client installation|started.]] </span>

: 2. <span class="f_ListNum1">Make sure debugging is turned on:</span>

* <var>Janus Debugger</var><span class="f_ListBul2">: Ensure you have done the [[Configure web browser (Janus Debugger only)|proxy server setup]] for whichever web browser you use.</span>
* <var>TN3270 Debugger</var><span class="f_ListBul2">: From the </span><var>Model 204</var><span class="f_ListBul2"> command line, issue the [[TN3270 DEBUG Syntax#TN3270 DEBUG ON|TN3270 DEBUG ON]] or the [[TN3270 DEBUG WAIT|TN3270 DEBUG WAIT]] command. Your session lasts until you log off </span><var>Model 204</var><span class="f_ListBul2"> or issue </span><span class="f_Monospace">[[TN3270 DEBUG Syntax#TN3270 DEBUG OFF|TN3270 DEBUG OFF]]</span><span class="f_ListBul2"> or the Debugger Client </span><span class="f_Monospace">[[turnOffDebugging command|turnOffDebugging]] </span><span class="f_ListBul2">command</span>

: 3. <span class="f_ListNum1">Run a request you want to debug: </span>

* <var>Janus Debugger</var><span class="f_ListBul2">: From your web browser, invoke a URL that accesses a SOUL program that is run by your </span><var>Janus Web Server</var><span class="f_ListBul2">.</span>
* <var>TN3270 Debugger</var><span class="f_ListBul2">: From the </span><var>Model 204</var><span class="f_ListBul2"> command line, start a SOUL program (Include a procedure or invoke an APSY subsystem).</span>

: 4. <span class="f_ListNum1">Using the Debugger Client GUI, control the execution of the SOUL code. </span>
:: You might take a few minutes with <span class="f_ListBul1">[[Getting Acquainted with the Client GUI|Getting Acquainted with the Client GUI]], then try</span><span class="f_ListContinue"> some of the operations described in </span><span class="f_ListBul1">[[Performing basic GUI tasks|Performing Basic GUI Tasks]]</span><span class="f_ListContinue">. </span>

[[Category:Debugger Home]]