JAL: add `s`

2018-03-16T21:27:39Z

add <var>s

← Older revision		Revision as of 21:27, 16 March 2018
Line 1:		Line 1:
	{{Template:M204.2304 skeleton}}		{{Template:M204.2304 skeleton}}

	<P>~~An attempt has been made to~~ RESET DKUPDTWT from zero to a non-zero value. However the CHKPTIMR PST was not attached during Model 204 initialization. Since nonzero settings of DKUPDTWT require use of the CHKPTIMR PST, the		<P>
	RESET command cannot be performed. </P>		A <code>RESET DKUPDTWT</code> from zero to a non-zero value was attempted. However the <code>CHKPTIMR</code> PST was not attached during Model 204 initialization. Since nonzero settings of <var>[[DKUPDTWT parameter\|DKUPDTWT]]</var> require use of the <code>CHKPTIMR</code> PST, the <var>RESET</var> command cannot be performed. </P>

	<p><b>System manager response:</b> The CHKPTIMR PST is attached during Model 204 initialization under either of the following circumstances: </p><ul>		<p><b>System manager response:</b> The <code>CHKPTIMR</code> PST is attached during Model 204 initialization under either of the following circumstances: </p>
			<ul>
	<li>DKUPDTWT > 0</li>		<li>DKUPDTWT > 0</li>
	<li>CPTIME > 0 and the X'01' bit of RCVOPT is on, the CHKPOINT stream is successfully opened, and sufficient pseudo subtasks are available (see NSUBTKS). </li>		<li>CPTIME > 0 and the X'01' bit of <var>RCVOPT</var> is on, the <var>CHKPOINT</var> stream is successfully opened, and sufficient pseudo subtasks are available (see <var>NSUBTKS</var>). </li>
	</ul>		</ul>
	<P>If you require the ability to change DKUPDTWT from zero to a nonzero value after initialization, then one of these conditions must be met during initialization. </P>		<P>
			If you require the ability to change <var>DKUPDTWT</var> from zero to a nonzero value after initialization, then one of these conditions must be met during initialization.
			</P>
	{{Template:M204.2304 footer}}		{{Template:M204.2304 footer}}
	<!-- skeleton as it was in pdf/RESET NOT ALLOWED, CHKPTIMR PST NOT ACTIVE /-->		<!-- skeleton as it was in pdf/RESET NOT ALLOWED, CHKPTIMR PST NOT ACTIVE /-->

DmeWiccan: Automatically generated page update

2018-03-14T03:40:47Z

Automatically generated page update

New page

{{Template:M204.2304 skeleton}}

An attempt has been made to RESET DKUPDTWT from zero to a non-zero value. However the CHKPTIMR PST was not attached during Model 204 initialization. Since nonzero settings of DKUPDTWT require use of the CHKPTIMR PST, the
RESET command cannot be performed. 

System manager response: The CHKPTIMR PST is attached during Model 204 initialization under either of the following circumstances: <ul>
<li>DKUPDTWT > 0</li>
<li>CPTIME > 0 and the X'01' bit of RCVOPT is on, the CHKPOINT stream is successfully opened, and sufficient pseudo subtasks are available (see NSUBTKS). </li>
</ul>
If you require the ability to change DKUPDTWT from zero to a nonzero value after initialization, then one of these conditions must be met during initialization. 

{{Template:M204.2304 footer}}

M204.2304 - Revision history

JAL: add s

DmeWiccan: Automatically generated page update

JAL: add `s`