Table X (File architecture)

Stores all Record Extensions in a separate table from the the base records (so that Table B contains only the base records).

Enabled by reorganizing / CREATEing a file with XSIZE greater than 0.

Available as of Model 204 V7.1

Summary

The Table B of a Model 204 file has a maximum number of 16.7 million record numbers (IRNs for Internal Record Numbers). By default (XSIZE = 0), these 'slots' are used for both base records and extension records.

By implementing Table X (XSIZE > 0) all defined IRNs (up to 16.7 million) in Table B are available for use by base records only, allowing the storage of the maximum possible number of records in a file regardless of the number of extensions.

Table X can be significantly larger than the 16.7 million limit of Table B; as the product of XSIZE * XRECPPG may be up to 512 million extension slots.

When the defined capacity of Table B or Table X is exceeded the file is marked full or the updating transaction is backed out.

Using Table X

While similar in concept to Table B, the actual 'extension record number' in Table X is far more straightforward.

• Because the number of slots in Table X is so large, and there is effectively no impact in wasting slots (until you approach that limit) XRECPPG can usually be set relatively high.

• Similarly, depending on how dynamic record growth is, you may wish to set XRESERVE higher than yopu would normally consider setting BRESERVE. This will enable records to grow without lengthening the extension chain.

• Table X slots are always reusable. There is no special setting (equivalent to FILEORG x'04') necessary to enable the use of the reuse queue.

RECRDOPT parameter

Table X may be implemented in one of two ways depending on the setting of the RECRDOPT parameter.

The default setting of the RECRDOPT (x'00')

If the default setting of RECRDOPT is used, while all extensions are stored in Table X, the record allocation in Table B is identical to what it is without Table X enabled.

BRECPPG remains the maximum number of records which may occur on a page, and so IRNs may still be wasted (never assigned to a record) as data fills up a page.

Setting RECRDOPT to x'01'

This setting changes the base record allocation to ensure that all defined IRNs are available for use.

For all x'01' RECRDOPT files, a base record size limit (the read only parameter BRLIMSZ) is calculated:

For an entry order file:

BRLIMSZ = (6140 / BRECPPG) - 2

For an unordered file:

BRLIMSZ = (6136 / BRECPPG) – 2

When a new record is stored, rather than using any and all space available on a page, only up to BRLIMSZ bytes will be stored in Table B. This ensures that the full BSIZE * BRECPPG number of IRNs can actually be stored in the file.

BRLIMSZ must be large enough to hold all preallocated fields.

(Note that the BRESERVE parameter is ignored with x'01' RECRDOPT files).

Advantages of Using Table X

Scalability

The obvious advantage of implementing Table X relates to the ability to store the full 16.7 million base records in a Model 204 file,

Indexing Performance

Even if a file has significantly fewer records than the limit, you should consider the performance of your indices in deciding whether to utilize Table X, notably where you expect to have fields with non unique values.

When Table X is enabled and RECRDOPT = x'01', the fact there are no wasted slots means that the bit maps containing the bitmap and list pages (and, of course, the Existence Bit Map) are as compressed as possible.

Avoidance of 'Sick Record' Snaps

When large sets of unlocked records (either through the use of Find Without Locks (FDWOL) or by referencing records on a Model 204 List) are processed, it is very possible that the records will have had their contents changed or even been deleted by the time the record is read. There are three problems that might be encountered when this happens:

the record should no longer be selected, its contents no longer matching the selection criteria

the record has been deleted (and so 'Nonexistent record' messages are produced)

the record now (due to delete and update processing) contains an extension record

The last of these problems causes a 'Sick Record' snap.

While Rocket encourages the use of coding techniques to prevent all of these issues, File Managers can protect themselves from the snaps (at least) by enabling Table X in files where such processing is expected.

The following Parameters relate to the Use of Table X

BRLIMSZ parameter	Calculated maximum size of base records
RECRDOPT parameter	Controls the method by which base records are stored
XQLEN parameter	The number of Table X pages in the reuse queue.
XRECPPG parameter	The maximum number of extension slots on a Table X page.
XRESERVE parameter	Table X reserve space per page
XREUSE parameter	Free space required to reuse a table X page
XREUSED parameter	The number of extension slots reused in table X
XSIZE parameter	The number of pages in Table X.

whose use is discussed in Sizing Tables B and X