Model 204 installation on IBM z/VSE

Note: This page is currently under construction.

Overview

This topic describes the steps required to upgrade from Rocket Model 204 version 7.4 to version 7.5, on the IBM^® z/VSE^® operating system.

For information on the new features available in version 7.5, see the 7.5 Release notes.

In order to upgrade to Model 204 version 7.5, you must have version 7.4 and the latest Autofix set of Early Warnings installed on your system.

To upgrade to version 7.5 simply download, upload, and link the 7.5 object modules available from the downloads page to install the 7.5 components.

Before you begin

• In order to upgrade to version 7.5, you must have version 7.4 and Autofix release EW3044 installed on your system.

  Autofix release EW3044 includes:

  • Early Warnings for Model 204 through 740EW172
  • Early Warnings for Dictionary/204 through 740DI016
  For information on Early Warnings, log in to the Rocket Customer Portal.

• For system requirements for version 7.5, see the 7.5 Release notes.
• You must have either a Rocket M204 user ID or a Sirius user ID to download the installation files.
• The sublibrary containing the object has the authorization zap (covering your licensed processors) preapplied, so you do not need to get a new authorization zap from the website.
  (The preapplied zap will authorize Model 204 itself and any separately purchased products such as PQO/204 and SirScan.)
• The object files also have the maintenance zaps (as of the time the stream was prepared) preapplied, so you do not need to apply any maintenance as part of this installation. (You will only need to apply any new maintenance when it becomes available for this release.)

Overview of upgrading steps

Review the following high-level summary of steps before you begin downloading the Model 204 version 7.5 files.

For an example, see Example workflow for 7.5: download through installation.

1. Use your Rocket M204 user ID to download the Model 204 object file and macro library.
2. Allocate the libraries.
3. Upload (FTP) the CATV750 job to the POWER RDR queue, CLASS=0, in binary format. This job will catalog object and JCL into each Model 204 sublibrary.
4. From the VSE console, release the CATV750 job from the RDR queue (R rdr,catv750). At the pause, enter the DLBL statements for your Model 204 library.
5. If you have your own user $functions (FUNU), you must do the following steps:
   1. modify FUNU for 64-bit addressing considerations and store the modified source in your V750 sublibrary.
   2. If you have any user-defined messages (MSGU), store them in your V750 sublibrary.
   3. Assemble FUNU (and MSGU, if applicable), with the output object file stored in your V750 sublibrary.
6. If you use customized modules, such as CDTB, modify them as needed and assemble them.
7. Link the ONLINE phase.
8. If you use the IFAM1 phase, link it.
9. Link the Model 204 utility programs.
10. If you use the CICS interface, customize it, and then assemble and link the CICS modules.
11. If your z/VSE site runs under z/VM, copy and link the $$BVP204 phase.
12. If you use SoftSpy, upgrade it for 7.5.

Model 204 disk space requirements

The following table summarizes the minimum disk space requirements for the libraries as well as other information to help you calculate EXTENT information for Model 204 files.

Minimum disk space requirements

Disk type	Minimum Model 204 library requirement	Bytes/track	Model 204 pages/track
3380	720 tracks	47476	7
3390	604 tracks	56664	8
9345	736 tracks	46456	6
FBA	67000 blocks	512 bytes/block	13 blocks/page

Allocating library space, defining sublibraries, and cataloging procedures

The M204CATP job allocates VSAM managed space for the Model 204 library, M204LIB, defines the sublibraries, and catalogs the two Model 204 procedures.

1. FTP the m204catp.y file to the mainframe in ASCII format.
2. Modify the M204CATP job as noted in the file.
3. Submit the M204CATP job.

Cataloging procedures

You can store some of the more frequently used JCL in the form of cataloged procedures. The jobs to catalog these procedures are distributed in the JCL sublibrary.

To catalog procedures, modify each procedure as follows:

• Add POWER JCL
• Add the appropriate DLBL, EXTENT, and ASSGN information

The jobs assume that the M204JCL procedure is in the system library (IJSYSRS.SYSLIB). All other Rocket-supplied procedures are cataloged into the JCL sublibrary. Determine the new file, library volumes, and extents; then modify the procedures before cataloging them.

Procedures that can be cataloged

As needed, you can modify and catalog the following procedures using the jobs listed in the following table.

Jobs for cataloging frequently used procedures

Procedure name	Catalog job	Description
M204WRK1	CATWRK1	Work file for translation and assembly
M204WRK2	CATWRK2	Work file for translation and assembly
M204SYS	CATSYS	System files (CCASYS, CCASTAT, CCATEMP)

Building the object and macro sublibraries

To build the object and macro sublibraries, you must download the object file and macro library and upload each to the mainframe.

Downloading

1. Using your Rocket M204 user ID and password, log in to the Model 204 object file download page.
2. Click the Download object file link beside the object library that you want to download.
3. Go to the Model 204 macro library download page.
4. Click the Download macro library link beside the macro library that you want to download.

Uploading (FTP)

Once the object and macro files are downloaded to your workstation, FTP them to the z/VSE system on the IBM mainframe.

Specify these characteristics for the upload files:

transfer format:	binary
record format:	FB
record size:	80 for object and macro libraries
block size:	6400 for object and macro libraries
storage size for both:	primary: 10 CYL; secondary: 5 CYL

For details on how to download and upload, see Downloading and uploading Model 204 installation components.

Reserving a partition

Rocket recommends a minimum partition size of eight megabytes (8M) when installing Model 204.

Some Model 204 installation JCL might assign system files/devices (SYSIPT, SYSPCH, etc.) to disk; z/VSE requires that this JCL be run in a static partition.

Space requirement for the Model 204 library

The M204CATP job distributed with the Model 204 software will allocate the appropriate space for the Model 204 library. In the sublibrary name, rrr represents the release level, such as 750.

Sublibrary	Required library blocks
Jrrr	700
Vrrr	17,800

Overview of the Model 204 library

The Model 204 library, M204LIB, is composed of sublibraries Jrrr and Vrrr, where rrr is the release level, such as 750. M204LIB contains all the materials needed to run the Model 204 z/VSE configurations (ONLINE, BATCH204, BATCH2, and IFAM1), and utilities.

Model 204 does not contain pre-linked phases. You must link all phases that you want to use.

CICS interface installation

The Model 204 CICS interface allows CICS complete access to Model 204 facilities and supports CICS pseudo conversational programs.

Note: It is not necessary to install the CICS interface if it has been installed for a previous version of Model 204. The load modules from the older version are compatible with version 7.5 of Model 204.

Requirements

• CICS Transaction Server support

  Rocket M204 supports the CICS Transaction Server versions 3.1, 3.2, 4.1, and 4.2.

• Supporting TPROCESS COBOL applications

  If your CICS TPROCESS application was originally linked with AMODE=24, you must relink the CICS TPROCESS application specifying AMODE=31 because AMODE=24 is not supported.

CICS interface overview

For an overview of the CICS interface, including storage requirements and a listing of CICS interface components, see CICS interface.

Installing the CICS interface

1. Customize the interface by editing the CICFG copy member and replacing it in the distribution library as CICFG.A. then proceed with the CICSASM and CICSLINK jobs.

   For information on customizations needed for using the CICS Standard Mapping Service, see CICS interface.

2. Update the CICS System Definition (CSD) using one of the following methods:
   • Resource Definition Online (CEDA).
   • The IBM DFHSCDUP offline utility, to process the definitions in batch.
   • Processing the CICS Program Control Table (PCT) and Program Processing Table (PPT).
3. Assemble, translate, and catalog the Model 204 CICS Interface modules, using the following jobs:
   • CRPSASM
   • ENTPSASM
   • OPLTASMC
   • PPCIASM
   • PRNTASMC
   • PSFASM
   • PSFSASM
4. Relink the IFAM2 transactions requiring pseudo conversational support with IFENTPS.
5. Relink all user process-to-process partners with IFPPCI.

Updating the CICS System Definition (CSD)

You can update the CSD by using CEDA, by using the DFHCSDUP utility, or by processing the CICS Program Control Table (PCT). Use the values in the following table, where appropriate, for the method you choose. Information about using CEDA follows the table.

CICS System Definition values

User program	Program name	Transaction ID	Modifiable CICFG symbol	TWA size
IFAM2 pseudo conversational	DFHPSF	DFHPSF is accessed by using a CICS LINK. It is never invoked with a transaction ID from a terminal.	N/A	N/A
Full-screen interface	M204PSFS	M204	&TRN	88
Screen copy transaction	M204CRPS	U204	N/A	N/A
Screen print transaction	M204PRNT	P204	&COP	88

CEDA (the Resource Definition Online transaction) or the DFHCSDUP utility defines the transactions and programs to the CSD file.

If you are not using tables, then define the transactions and programs by using CEDA and the values in the previous table, as in the following example:

CEDA DEFine PROG(program_name) GRoup(group_name) LANGuage(ASSEMBLER) RELoad(NO) RESident(NO) (Except for DFHPSF, RESident(YES)) STatus(ENABLED) CEDA DEFine TRANsaction(trans_ID) GRoup(group_name) PROgram(program_name) TWASIZE(twa_size_value) . . . CEDA CHeck GRoup(group_name) CEDA INstall GRoup(group_name)

You can use a transaction ID for a user program that is different from the value shown in the previous table. However, if you do so, you must change the associated CICFG symbol shown in the table.

As shown in the preceding example, group_name is any valid group name for the user site.

Note: Remember to add the groups to the GRPLIST for the particular CICS region. If the groups are not added, they are not installed during each CICS initialization.

Processing the PCT and PPT

The JCL sublibrary members PCTNTRY and PPTNTRY have the Program Control Table (PCT) and the Program Processing Table (PPT) default values shown in the following code. You can update the CSD by adding to or modifying these default values and then assembling the tables.

PCT: Program Control Table

The Program Control Table (PCT) assigns user programs to their related CICS transaction identifiers (the transaction codes). Entries are required for both the 3270 full-screen interface and the screen print transaction.

The JCL sublibrary member, PCTNTRY, contains the PCT default values shown in the following code:

DFHPCT TYPE=ENTRY,PROGRAM=M204PSFS,TRANSID=M204,TWASIZE=88 DFHPCT TYPE=ENTRY,PROGRAM=M204PRNT,TRANSID=P204,TWASIZE=88 DFHPCT TYPE=ENTRY,PROGRAM=M204CRPS,TRANSID=U204

The following entry in the PCT is required for all user IFAM2 transactions:

DFHPCT TYPE=ENTRY,PROGRAM=program_name,TRANSID=xxxx,TWASIZE=88

Use the values in the previous table if you are updating the PCT. If you use a transaction ID for a user program that is different from the value shown in that table, you must change the associated CICFG symbol.

PPT: Program Processing Table

The Program Processing Table (PPT) stores program attributes. Entries are required for the 3270 full-screen interface, direct printer support, and the IFAM2 interface.

The JCL sublibrary member, PPTNTRY, contains the PPT default values shown in the following code.

Note: In the first line of the PPT, be sure to set the RES parameter to YES; otherwise, the transaction does not complete successfully.

DFHPPT TYPE=ENTRY,PROGRAM=DFHPSF,RES=YES,PGMLANG=ASSEMBLER DFHPPT TYPE=ENTRY,PROGRAM=M204CRPS,PGMLANG=ASSEMBLER DFHPPT TYPE=ENTRY,PROGRAM=M204PRNT,PGMLANG=ASSEMBLER DFHPPT TYPE=ENTRY,PROGRAM=M204PSFS,PGMLANG=ASSEMBLER DFHPPT TYPE=ENTRY,PROGRAM=OBPLTSD,PGMLANG=ASSEMBLER

Assembling the CICS Interface modules

Assemble, in the sequence listed, the CICS Interface modules listed in the assembly step in the CICS interface installation section.

Some assemblies display a warning message (DFHEIMSG 4) because the CSA address is release-dependent. If the interface program is running in the release under which it was assembled, ignore the warning.

After the modules are successfully built, relink as directed in the CICS interface installation section.

Preparing site-specific CDTB, FUNU, and MSGU modules

CDTBASMC, FUNUASMC, and MSGUASMC jobs

If you use translation tables or user-written functions, you must change the source code in the CDTB.A, FUNU.A, and MSGU.A sublibrary members to accommodate the requirements of your site, as shown in the following table.

Customizable user modules

If you use...	Then do this...	Using this job
$CODE and $DECODE functions to encode and decode character strings	Edit your own translation tables into the CDTB.A member	CDTBASMC
Your own User Language functions	Add them to the FUNU.A member	FUNUASMC
Error messages with your own User Language functions	Modify the MSGU.A member	MSGUASMC

The FUNU.A member contains one user function, $SEP, which adds separators when a date is entered in the format mm/dd/yy. MSGU.A also contains one sample error message.

You can use FUNU.A and MSGU.A to write your own user functions. The steps for installing the modules, as well as assembly considerations, are provided here.

It is recommended that if you think your site will make use of the TCP/IP Sockets Interface for Model 204, link the FUNU.A member during the installation process, even if you have not yet developed your own functions. This ensures access to the $ASCII and $EBCDIC functions.

Assembling CDTB, FUNU, and MSGU

The following table identifies the JCL to assemble CDTB, FUNU, and MSGU and catalog the object decks into the Model 204 sublibrary.

JCL library member for user modules

Member	Assembles and catalogs user modules
CDTBASMC	CDTB (code table)
FUNUASMC	FUNU (functions)
MSGUASMC	MSGU (messages)

Once the modules are assembled and cataloged, link the Model 204 phases to contain user code tables and/or user functions, specifying the M204LIB.Vrrr sublibrary containing the CDTB, FUNU, and MSGU modules in the search list.

The M204LIB.Vrrr sublibrary members LKONLN and LKB204 distributed with this version contain the INCLUDE statements for CDTB, FUNU, and MSGU.

Assembly considerations for FUNU and MSGU

Some of the Model 204 macros and copy code needed to assemble FUNU and MSGU contain assembly language statements that are not supported by the z/VSE assembler. An assembly error occurs in the following circumstances:

• EQU statement specifies a length attribute or type attribute. The following example from the VARDEFS copy book illustrates the error:

  VISLVL EQU 0,1 FIELD SECURITY LEVEL

  The error generated for this statement is:

  IPK122 INVALID DELIMITER, ',1'

• EQU statement specifies a value that is too long or too large by assembler rules. The following example from the STARTS macro illustrates the error:

  MAXFS EQU 16777216/(4096*8) .MAX NUMBER OF INTERNAL FILE SEGMENTS

  The error generated for this statement is:

  IPK117 VALUE OF SELF-DEFINING TERM '16777216' TOO LARGE

  See the z/VSE assembler error message IPK117 for more information.

• Symbol defined by an EQU statement of the type described above is referenced in a subsequent assembler statement. The following example from the STARTS macro illustrates the error:

  IVBN EQU ((MAXFS+7)/8). MAX # OF BYTES IN SEGMENT BIT PATTERN

  Where the error occurs because MAXFS is undefined (see the example in the second bullet, above), the error generated for this statement is:

  IPK149 SYMBOL 'MAXFS' NOT PREVIOUSLY DEFINED

• In FUNU, some undefined symbols generate the following statement:

  QW9 ***** UNDEFINED *****

  The error generated for this statement is:

  IPK149 SYMBOL 'QW9' NOT PREVIOUSLY DEFINED

The text generated is executable and executes properly (barring logic errors) unless code that references an undefined symbol is executed.

Assembling FUNU and MSGU generates the errors described. However, in FUNU, no assembly errors occur within the FUNUTAB table entries or within the code for a user function (between the $name ENTER statement that begins the function and the LEAVENUM, LEAVESTR, or LEAVEF0 macro that terminates it). In MSGU, no assembly errors occur after the MSGU$ CSECT statement. CDTB receives no assembly errors.

z/VSE assembler errors

Rocket Software takes no responsibility for the errors generated by the z/VSE assembler. It is your responsibility to ensure that you do not code user functions referencing symbols that are undefined due to an assembler error.

Linking the $$BVP204 phase

The following information applies only to z/VSE sites running under z/VM.

The $$BVP204 phase is a transient: it is required for the z/VM-directed output feature, and it is invoked by Model 204 to issue diagnostic instructions in order to pass CP commands to z/VM.

Linking $$BVP204 to the system library improves performance.

LINK$BVP job

To link $$BVP204, use the LINK$BVP job from the M204LIB.Jrrr sublibrary.

This is a required step in a Model 204 installation on z/VSE running under z/VM.

COPYVMPR job

To copy $$BVP204 to the System Residence Library, use the COPYVMPR job from the M204LIB.Jrrr sublibrary.

This is a required step in a Model 204 installation on z/VSE running under z/VM.

Installing terminal access methods and communications features

This section presents basic steps for installing these terminal access methods and communications features:

• Model 204 Virtual Telecommunications Access Method (VTAM) Interface.
• Horizon for TCP/IP intersystem communication feature, which is required for Connect★ support.
• Parallel Query Option/204, which enables distributed file processing.

Installing the VTAM Interface

Installing Model 204 with VTAM requires defining Model 204 as a VTAM application program. Model 204 provides 3270 support, as well as VTAM support for full-screen terminals that are not 3270-compatible, by providing a mechanism for writing exit routines to convert data outside of the VTAM 3270 interface.

Rules governing data conversion exit routine coding are described in Coding SNA Communications Server conversion exit routines.

To install the VTAM Interface, perform these steps:

Step	Task	Job
1.	Make sure that INCLUDE LKVTAM is authorized.
2.	Define Model 204 as a VTAM application node using an APPL statement in VTMAPPL.B.	N/A
3.	Link edit the Model 204 ONLINE phase.	LINKONLN

Specifying a VTAMNAME

The network name of the Model 204 run is specified for VTAM in the Model 204 system parameter VTAMNAME. The VTAMNAME parameter in CCAIN is the same as the APPL statement name field.

The value of VTAMNAME is a string composed of 1-8 characters. The default is M204. VTAMNAME can be specified by the system manager on the User 0 parameter line.

For more information on VTAM parameters, see Defining the user environment (CCAIN).

Installing the Horizon Interface

The Horizon for TCP/IP intersystem communication feature is required for Connect★ and TCP/IP support.

To install the Horizon Interface, perform these steps:

Step	Task	Job
1.	Make sure that INCLUDE LKHRZN is authorized.
2.	Link edit the Model 204 ONLINE phase.	LINKONLN

For more information about Horizon, see the Rocket Model 204 Horizon: Intersystem Processing Guide.

Installing Parallel Query Option/204

Parallel Query Option/204 (PQO) enables distributed file processing.

To install PQO, perform these steps:

Step	Task	Job
1.	Make sure that INCLUDE LKPQO is authorized.
2.	Link edit the Model 204 ONLINE phase.	LINKONLN

For more information about PQO, see the Parallel Query Option/204 User's Guide.

Installing CRAM

The Cross-Region Access Method (CRAM) lets two or more Model 204 users in two or more partitions communicate with each other. CRAM is used by:

• BATCH2
• CICS Interface
• IFAM2

See Defining the user environment (CCAIN) for more information about CRAM.

Linking the CRAM phases

To link the CRAM phases (CRAMSWT, CRAMZWT, IGCLM244, and SNAPCRAM), use the LINKCRAM job from the JCL library.

Link editing the Model 204 phases

You must link all required phases and any optional phases that you want to use, including utilities and sort exits.

To link any of the Model 204 phases, run the job listed for that phase in the following table. This table also lists utilities you might need and the jobs used to link or relink them.

Phases listed as Optional might be needed at your site depending on your installation requirements.

Executable phases and jobs used for linking or relinking

Phase or utility	Purpose / Notes	Job	For more details, see ...
$$BVP204	z/VM-directed output logical transient. Required on z/VSE systems running under z/VM.	LINK$BVP	Linking the $$BVP204 phase
ALLOCATE	Initializes Model 204 database files Required for Installation JCL, SQL installation, and Dictionary/204	LINKALOC	ALLOCATE utility in z/VSE
AUDIT204	Generates an audit trail for printing out later, and produces statistical reports and analysis	LINKAUDT	AUDIT204 utility
BATCH2	Establishes a User Language connection to a Model 204 ONLINE running in a separate region Optional; recommended for CRAM testing.	LINKBAT2	BATCH2 (TCP/IP)
BATCH204	Handles a single user in batch mode Required to complete installation Link or relink when: Installing user modules CDTB, FUNU, MSGU Installing or upgrading to a new release of Model 204 Moving to a different release of CICS (M204 CICS Interface)	LINKB204	Linking the BATCH204 phase
CRAMSWT	CRAM non-master subtask	LINKCRAM	Installing CRAM
CRAMZWT	CRAM master subtask	LINKCRAM	Installing CRAM
DFHPSF	CICS/IFAM2 Interface	PSFASM	Updating the CICS System Definition (CSD)
HASH15	Sort exit for M204HASH	LINKHA15	Using M204HASH in the z/VSE environment
IFAM1	Host Language Interface single-thread configuration Link or relink when installing or upgrading to a new release of Model 204. (You can ignore UNRESOLVED ADCON messages.)	LINKIFM1	IFAM1
IGCLM244	CRAM load module	LINKCRAM	Installing CRAM
M204CRPS	CICS full-screen printer routine	CRPSASM	Updating the CICS System Definition (CSD)
M204L	Loads an M204 phase above the line	LNKM204L	Link editing the M204L phase
M204PRNT	CICS 3270 print routine	PRNTASMC	Updating the CICS System Definition (CSD)
M204PSFS	CICS full-screen remote User Language interface routine	PSFSASM	Updating the CICS System Definition (CSD)
MERGEJ	Media recovery journal merge utility	LINKMRGJ	Using the MERGEJ utility
OI15	File Load utility sort exits	LINKOI15	Deferred update feature
OI35	File Load utility sort exits	LINKOI35	Deferred update feature
ONLINE	Link online; Required. Link or relink when: Installing VTAM, Horizon, or Parallel Query Option/204 Installing user modules CDTB, FUNU, MSGU Installing or upgrading to a new release of Model 204 Moving to a different release of CICS (M204 CICS Interface)	LINKONLN	Linking the ONLINE phase
SNAPCRAM	CRAM control block SNAP dump routine	LINKCRAM	Installing CRAM
UTILC	Prints the Model 204 checkpoint file	LINKUTLC	Obtaining checkpoint information (UTILC)
UTILJ	Prints and copies Model 204 journal files	LINKUTLJ	Using the UTILJ utility
UTLA	Prints the Model 204 audit trail	LINKUTLA	z/VSE and the audit trail
ZBLDTAB	Initializes the Model 204 password table. Required to allocate and initialize CCASTAT.	LINKZBTB	Storing security information (CCASTAT)
ZCTLTAB	Convert CCASTAT for the Password Expiration feature. Required to convert an existing CCASTAT data set to allow data control of passwords.	LINKZCTB	Storing security information (CCASTAT)

Linking the ONLINE phase

LINKONLN is the JCL member for linking the ONLINE phase and contains INCLUDE statements for a base loadlist and for each feature.

Because the features for CICS do not affect the ONLINE phase, no specific loadlists are necessary for this feature.

Linking the IFAM1 phase

LINKIFM1 is the JCL member for linking the IFAM1 phase and contains INCLUDE statements for a base loadlist as shown in the following table.

Loadlists for IFAM1 and features

Loadlist	IFAM1 or feature
LKIFM1	IFAM1

The sample LINKIFM1 JCL is prepared to link IFAM1.

LINKIFM1 JCL example // EXEC PROC=M204JCL DLBL for JCL sublibrary // LIBDEF PROC,SEARCH=M204LIB.Vrrr // EXEC PROC=M204Vrrr DLBL for Vrrr M204 library // LIBDEF PHASE,CATALOG=M204LIB.Vrrr // LIBDEF OBJ,SEARCH=M204LIB.Vrrr // OPTION CATAL PHASE IFAM1,* REPLACE=YES INCLUDE LKIFM1 ENTRY IFII1 /* // EXEC LNKEDT /* /&

where rrr is the release level, such as 750.

Linking the BATCH204 phase

LINKB204 is the JCL member for linking the BATCH204 phase and contains INCLUDE statements for a base loadlist, as shown in the following table.

Loadlists for BATCH204 and features

Loadlist	BATCH204 or feature
LKBTCH	BATCH204

The following sample LINKB204 JCL is prepared to link BATCH204.

LINKB204 JCL example

// JOB LINKB204 * ******************************************************************** * Rocket Model 204 * 02/15 * ******************************************************************** * LINKB204 links/catalogs the MODEL 204 BATCH204 phase /* /* Note: if using LE functions in MODEL 204, /* - add INCLUDE statements for LE modules /* - concatenate appropriate sublibrary to search. /* // EXEC PROC=M204JCL DLBL for JCL sublibrary // LIBDEF PROC,SEARCH=M204LIB.V750 // EXEC PROC=M204V750 DLBL for V750 M204 library // LIBDEF PHASE,CATALOG=M204LIB.V750 // LIBDEF OBJ,SEARCH=M204LIB.V750 // OPTION CATAL PHASE BATCH204,* REPLACE=YES * INCLUDE LKNOSONL /* Uncomment for Pattern Matcher * INCLUDE LKSQLONL /* Uncomment for Remote SQL and Pattern Matcher ENTRY MAINTASK /* // EXEC LNKEDT /* /&

where rrr is the release level, such as 750.

Link editing the M204L phase

To run above the line (in 31-bit addressing space), you need to link the M204L program, which acts as an intermediary to load M204 phases above the line.

In the PARM clause of the EXEC statement, indicate the M204 load module that M204L will load above the line.

In the following example, ONLINE will be loaded above the line and then invoked:

// EXEC M204L,SIZE=AUTO,PARM='ONLINE'

The following sample LNKM204L JCL is prepared to link M204L.

// JOB LNKM204L * ******************************************************************** * Rocket Model 204 * 02/15 * ******************************************************************** * LNKM204L links/catalogs the MODEL 204 M204L phase /* /* // EXEC PROC=M204JCL DLBL for JCL sublibrary // LIBDEF PROC,SEARCH=M204LIB.V750 // EXEC PROC=M204V750 DLBL for V750 M204 library // LIBDEF PHASE,CATALOG=M204LIB.V750 // LIBDEF OBJ,SEARCH=M204LIB.V750 // OPTION CATAL ACTION ERRLMT(500) PHASE M204L,* REPLACE=YES INCLUDE M204L /* // EXEC LNKEDT /* /&

Link editing messages

When link editing any Model 204 programs, the following messages appear one or more times in the output listing:

2139I DUPLICATE SECTION DEFINITION: COPR *** SECTION IGNORED *** 2158I NO CSECT LENGTH SUPPLIED

These messages result from the linkage editor flagging any duplicate CSECT as an error in a new release of system software. If the message reads exactly as above, you can ignore it. If, however, the error message displays anything other than COPR, contact Technical Support.

Also, you will typically see Unresolved External warnings for the following references, which you may ignore: FORTRAN modules such as DTRNH, DSQRT, and so on.

Creating password and file group data sets

Before running ONLINE, BATCH204, or IFAM1 programs, prepare the following files:

File	Type of data set
CCAGRP	File group data set (required for file groups)
CCASTAT	Password data set (required)
CCATEMP	Scratch data set (required). See Allocating CCATEMP for information about the scratch data set.

CCAGRP: Using permanent file groups

Before you can define permanent file groups in Model 204, you must allocate and initialize the CCAGRP file. For more information, see Storing and using file group definitions (CCAGRP).

ALOCGRUP job

Follow these steps to name and size the CCAGRP file:

1. Allocate CCAGRP with the ALOCGRUP job.
2. Modify the ONLINE, BATCH204, and IFAM1 JCL streams.
3. Issue the CREATEG command to initialize CCAGRP.

CCASTAT: Building the Model 204 password table

If your site intends to use Model 204 security features, you must build the password table in the CCASTAT file. To access CCASTAT, modify the ONLINE, BATCH204, and IFAM1 JCL streams.

ZBTBRUN job

Follow these steps to build the password table by creating CCASTAT:

1. Allocate and initialize the CCASTAT file by running the ZBTBRUN job, which executes the ZBLDTAB utility program. The amount of disk storage allocated must be sufficient to contain:
   • Two Model 204 pages (each page is 6184 bytes) for CKD devices.
   • Minimum allocation of 26 blocks for FBA devices.
2. ZBTBRUN does not usually produce a return code. Look at the listing for any indication of a problem.
3. Modify ONLINE, BATCH204, and IFAM1 JCL streams. When executing the ONLINE, BATCH204, or user-written IFAM1 program that uses this security file, add this label information in the execution JCL stream:

   // DLBL CCASTAT,'M204.CCASTAT',0,SD // EXTENT SYSnnn,volser,,,start,length

Updating the password table

You must provide the full CCASTAT file information for the execution of ONLINE or BATCH204 if you plan to update the password table with the LOGCTL command. When you update the password table, Model 204 opens the file as an output data set and completely rewrites it. It is recommended that you set the retention period for the CCASTAT data set at zero to avoid operator intervention.

Activating security

In addition, to activate the security facilities of Model 204, turn on UPSI switch 3 (SYSOPT=16):

// UPSI xxx1xxxx

You can use the LOGCTL command to create entries in the password table.

Creating a Password Expiration CCASTAT

If your site would like to use the optional security feature that allows date control of passwords, you must convert an existing CCASTAT data set. This conversion may be run at any time and is irreversible.

Note: It is strongly recommended that you save a copy of the original CCASTAT file before converting it.

(If you need to create a CCASTAT file, see the wiki topic on CCASTAT.)

Running the ZCTBRUN job

Follow these steps to convert a CCASTAT data set using the ZCTLTAB utility.

1. Read the description of ZCTLTAB options, and read the comments found in the job ZCTBRUN.
2. Save a copy of the original, unconverted CCASTAT file.
3. Modify job ZCTBRUN as needed and run it. This will run ZCTLTAB to convert the CCASTAT data set.

Allocating CCATEMP

CCATEMP is a required data set used by Model 204 as the system scratch file.

Allocate CCATEMP before running jobs that execute an ONLINE, BATCH204, or IFAM1 program.

1. Calculate the size of CCATEMP:

   Allocate a minimum of 25 pages per user if your site uses file groups, otherwise allocate 20 pages per user.

2. Allocate CCATEMP with the ALOCTEMP job.

Upgrading SoftSpy for 7.5

To upgrade SoftSpy for version 7.5, download, upload, and restore the SoftSpy procedure file, SPYPROC, which is distributed in a dump format.

1. Download SPYPROC, in binary form, from the SOUL files download page to a workstation file.
2. Upload (FTP) the file from your workstation to your z/VSE system.
3. RESTORE the file into a Model 204 SOUL file.

For detailed instructions, see the dump files section of Downloading and restoring SOUL files.

Verifying Model 204 7.5 on your system

To perform an initial verification that your upgrade to 7.5 was successful, issue the following commands from the Model 204 command line.

Command	You should see...
ROCKET	A list of authorized M204 products (including 7.5) currently on your system.
DISPLAY ZAPS	A list of Model 204 zaps (including 7.5 zaps) on your system.
DICTADMIN	The Dictionary Administration subsystem, displaying Release 7.5 on its menu screens.
SUBSYSMGMT	The Application Subsystem facility, displaying VER 7 REL 5 on its menu screens.